ViseeO MB-2 User Manual

User Manual Preface This publication, including all photographs, illustrations and software, is protected under international copyright laws, with

10 Original phone cradle and UHI connector 2. Installation 2.1 Installing the Main Unit ViseeO MB-4 is designed to work with a pre-installed UHI/MH

11 3. Basic Operation 3.1 Pairing for the First Time Once you have installed your MB-4 in the vehicle, you need to pair it with you

12 DEVICE FULL!FREE UP SPACE? YESorder to allow automatic reconnection each time you re-enter your vehicle please select “Yes” when you see this typ

13  If you switch to a phone that is not nearby or its Bluetooth is not switched on you will get a message “Not found” and followed by “No Phone D

14 4. Phonebook Function 4.1 Sync Phonebook If your phone supports the phonebook sync protocol provided by MB-4 you will be able to take the ad

15 phonebook entries under Object Push Profile (OPP) mode (see Section 4.2 Manually Upload Phonebook for further information).  Phoneb

16 2. Browse with [] to [SEND CONACT]. 3. Press [OPP] to activate OPP mode. 4. Access your phonebook on your phone now and go to the

17 To upload phonebook entries from MB-4 to NTG 4: 1. After connecting MB-4 with your mobile phone wait for “Activating Telephone…” mes

18 phone. If you wish to skip the auto sync of your phonebook every time you re-enter your car you can turn this function OFF. To enable/disable aut

19 5. Advanced Bluetooth Setting 5.1 Disconnect from the Current Connected Device To disconnect from the current connected device: 1. Press [ME

2 Foreword & Important Note on Safety!! (MUST READ) Please read this note before you install and use MB-4 Bluetooth Upgrade Adaptor! Congratula

20 5.3 Remove a Paired Device To remove a paired device: 1. Press [MENU] in standby mode. 2. Browse with [] to BLUETOOTH and press the [SETU

21 6. Other Advanced Settings 6.1 Microphone Volume Setting To setup microphone volume: 1. Press [MENU] in the standby mode. 2. Browse with [

22 the phonebook entries, ViseeO MB-4 allows you to reset it back to the original factory settings. To master reset ViseeO MB-4: 1. Press [MENU] in

23 is the operating system of MB-4. Both types of updates may be revised from time to time and available for you to download from www.viseeo.com.

24 2. Browse with [] to PIN SELECTION and press [SETUP] to enter this setting. 3. Press [SEL] to choose either PIN:1234 or PIN:0000. 4. Press [

25 7. Miscellaneous 7.1 Trademark  The Bluetooth logos are registered trademarks owned by Bluetooth SIG, Inc, and any use of such marks in this

26

3 QUICK START GUIDE CAUTION!! DO NOT ATTEMPT TO INSTALL THE UNIT WHILE THE CAR IS IN MOTION! INSTALLING MB-4 (For detailed instruction please see S

4 MAKING A CALL (For detailed instruction please see Section 3.4 Making the First Call) 1. Connect your phone with MB-4. 2. Dial a set of numbers yo

5 Preface... 1 Forewo

6 1. Understanding Your MB-4 1.1 Package Contents 1. MB-4 main unit. 2. USB to mini USB cable. 3. ViseeO Software Upgrade Cable.  

7 1.2 MB-4 Main Unit & Descriptions 5V Mini USB Charging PortQuick Switch for Paired Phones/Menu Browsing ButtonSYNC now/ Return/Cancel ButtonM

8 1.4 MB-4 Keypads and Functions Each key corresponds to a designated command shown on the display Left Key SYNC Now, Return to Upper Level Menu

9 Original software switch position for Non-NTG4 vehicles Software switch position for W204, W212, W207 and other NTG 4 vehicles The factory default